Mixer tap or two-handle faucet: what’s the difference and which should you choose?
Lucas Morel
Key takeaways
- A mixer tap controls flow and temperature with a single lever, thanks to a ceramic disc cartridge.
- A two-tap mixer has two separate taps, one for hot water and one for cold water, connected to a single spout.
- A thermostatic mixer tap reduces water consumption by 10 to 30% compared to two conventional taps, according to the CIEau.
- An eco-flow aerator reduces flow from 12 to 8 litres per minute at 3 bars for any tap.
Between a mixer tap and a two-tap mixer, the mixer tap wins on convenience and savings: a single lever, temperature restored in one motion, and 10 to 30% less water used. The two-tap mixer retains the advantage of a traditional style and easy repair.
Both taps deliver the same water through the same spout. What changes is the hand that mixes it. With two crosshead handles, you have to turn one, wait, adjust the other, and water runs down the drain in the meantime. The difference is also visible in the decor: an antique bronze brass model defines a period bathroom, while a matte black mixer tap matching the accessories suits a modern room. This guide compares the two solutions, then gives the right choice for each room.
What is the difference between a mixer tap and a two-tap mixer?
The difference between a mixer tap and a two-tap mixer lies in the number of handles. The two-tap mixer has two, which separately control the hot and cold water before a common spout. The mixer tap combines both inlets behind a single handle.
What is a mixer tap, technically? A tap whose lever is lifted to control flow and turned to adjust the temperature, thanks to two ceramic discs sliding in a cartridge. The two-tap mixer, on the other hand, is adjusted in two motions, with a compression valve or ceramic head on each side.
| Comparison point | Mixer tap | Two-tap mixer |
|---|---|---|
| Operation | A single lever | Two crosshead or round handles |
| Temperature | Retained when closed | Must be reset each time it is opened |
| Drilling | Usually single-hole | Single, two or three-hole |
| Typical failure | Leaking or seized cartridge | Worn washer or valve |
Product listings also use one term for the other: count the handles before comparing basin mixer taps and two-tap mixers.
Mixer tap or two-tap mixer: which uses the least water?
A mixer tap uses less water than a two-tap mixer because it shortens the time spent finding the right temperature, during which water runs at full flow into the basin or sink.
10 to 30%
The Centre d'information sur l'eau states that a thermostatic mixer tap « reduces your water consumption by 10% to 30% » compared to standard two-tap mixers.
Que Choisir applies the same range to a single-lever sink mixer tap. Flow rate, however, has a greater impact than the type of tap: an aerator screwed onto the spout reduces flow from 12 to 8 litres per minute.
The central position trap
On a conventional mixer tap, the centre lever already delivers hot water. Hansgrohe's CoolStart documentation estimates the difference at 508 kWh per year for four people, 20 minutes a day, based on German assumptions. For a glass of water, push the lever towards the cold setting.
What are the advantages of a mixer tap?
The advantages of a mixer tap are convenience and ease of use. One hand is enough, a particularly useful gesture in the kitchen. The temperature is remembered: you close it by lowering the lever, and the flow is easily adjusted.
For children's safety, a mixer tap is no guarantee: a lever pushed to the left delivers the hottest water from the boiler. Some cartridges accept a stop ring that limits the movement towards the hot setting, which should be checked in the instructions.
Single-hole, high spout for a countertop basin, concealed wall-mounted version or surface-mounted two-tap mixer: each installation changes the height of the spout and the clearance around the basin.
Compare basin tapsWhat are the disadvantages of a two-tap mixer?
The disadvantages of a two-tap mixer come from its manual adjustment. Each opening requires it to be adjusted again, and a drop in pressure on one side changes the temperature without warning. Its strong point remains its technical simplicity: a compression head can be dismantled with an open-ended spanner, and its washer can be bought at a DIY store.
Maintenance and failures: which tap lasts the longest?
The lifespan of a tap depends mainly on limescale and the quality of the parts. On a mixer tap, limescale jams the cartridge: the lever becomes stiff, then a leak appears. On a two-tap mixer, the washer and valve wear out. A quarterly check of the aerator, unscrewed and rinsed with white vinegar, limits limescale build-up.
Before dismantling
Close the stop valves under the cabinet, or the main water supply, then open the tap to release the pressure. For anything other than an identical replacement, entrust the plumbing to an expert.
A cartridge can be replaced in half an hour: take the old cartridge with you to the store. The MÉRIDIEN product sheet from Aeraly thus indicates a Wanhai cartridge and a 3-year warranty. If the body is covered in limescale, it is better to remove the old mixer tap and install a new mixer tap on the same flexible hoses.
Which tap is the most economical?
At purchase, prices overlap: the material matters more than the system. A solid brass or stainless steel body costs more than a zamak body, but resists moisture better.
As of October 15, 2026, the Aeraly collection includes 19 published taps: the CORNIOLA single-hole mixer tap starts at 170 euros, the PINO surface-mounted two-tap mixer in solid brass costs 249.95 euros, and the high-end MÉRIDIEN 3-hole wall-mounted tap with curved spout reaches 435 euros. In use, the mixer tap becomes the most economical.
And the thermostatic mixer tap?
The thermostatic mixer tap is a third type of tap. Its technology separates temperature and flow on two handles, and a heat-sensitive element automatically corrects the mixture when the pressure varies.
Its main place is the shower. A stop prevents the temperature from exceeding a comfort threshold, a useful feature with children. It costs more and is more sensitive to limescale. Before deciding, it is better to compare thermostatic and mechanical on your shower column, then plan a tap set at the right level on the wall.
Mixer tap or two-tap mixer: which to choose according to use?
The choice between a mixer tap and a two-tap mixer is made room by room. The main criterion is the frequency of use: the more often and briefly the tap is opened, the more useful the mixer tap is.
| Use | Advice |
|---|---|
| Bathroom basin | Single-hole mixer tap |
| Shower | Thermostatic |
| Bathtub | Bath-shower mixer tap |
| Kitchen sink | High-spout mixer tap |
| Retro decor | Two-tap mixer with crosshead handles |
For kitchen taps, the mixer tap dominates: you open it with the back of your hand above the worktop, and an extractable hand shower rinses the large or double sink. The two-tap mixer retains its place in vintage decor, with subway tiles or a clawfoot bathtub.
Frequently asked questions
Can you replace a two-tap mixer with a mixer tap without changing the basin?
Yes, if the basin has a single hole: a single-hole mixer tap can be fixed directly. A two or three-hole model leaves empty holes in the ceramic. The solution then involves a 3-hole mixer tap, a cover, or a wall-mounted installation.
What does the ECAU rating on a tap mean?
The ECAU rating, issued by the CSTB, evaluates sanitary taps on four criteria: water savings related to flow rate, comfort, acoustics, and wear. According to Batiweb, each criterion is rated from A to D since the new display presented in 2019.
Can you install a mixer tap yourself?
Yes for an identical surface-mounted replacement: close the water, unscrew the flexible hoses, remove the mounting nut, then install the new tap, in about an hour. A concealed wall-mounted version, whose body is placed before the tiling, requires a plumber.
Conclusion
The mixer tap wins on almost all daily points: one hand is enough, water is saved, and the temperature remains set. The two-tap mixer retains two real assets, a simple-to-repair mechanism and an old style that no lever can imitate. Our advice before buying: count the holes, measure the height of the spout, and check the network pressure. For the shower, reserve the budget for the thermostatic. On the old tap, an 8-litre-per-minute aerator remains the most cost-effective choice.
An independent writer, he writes the Aeraly blog guides and compares bathroom taps on their mechanisms, failures, and water consumption.
Published on November 17, 2026